|
|
Hours of Operation:
Mon-Fri: 8am - 5pm
Eastern Standard Time
26200 Groesbeck Hwy.
Warren, MI 48089
|
Stay green with our environmentally friendly waterborne epoxy floor coating kits.
|
|
|
|
Waterborne Epoxy Gloss Topcoat
( Product Date Sheet )
|
Waterborne Epoxy Polyamide
General Description: |
|
A high performance, two-package, chemically-cured waterborne gloss epoxy coating for use as a hard, durable high performance architectural coating (HIPAC). Features easy application, low VOC, high flash point, lower odor than solvent-based epoxies, and a hard, tough, stain-resistant finish. May be used in areas subject to continuous high moisture such as shower rooms.
|
|
Use on interior properly prepared poured concrete, concrete block, drywall, metal and wood. Ideal for hard usage areas of schools, hospitals, restaurants, public buildings and factories.
|
|
Suitable for use on structural surfaces or surfaces where there is a possibility of incidental food contact in commercial food preparation establishments, food processing plants and federally inspected meat and poultry plants. USDA no longer
requires or furnishes product certification letters.
|
Color: Clear
Finish: Gloss, 90 units minimum @ 60°
Clean-up Solvent: Soap and water
Weight/Gallon (mixed): 10.1lbs./gal. (1.21kg/L)- varies with color
VOC (mixed): 1.72 lbs./gal. (206 g/L) - varies with color
Solids By Volume (mixed): 43% ± 1% - varies with color
Theoretical Coverage at 1.0 Mil Dry: 690 sq.ft./gal.(17 m2/L)
Practical Coverage: Apply at 235-320 sq. ft./gal. (6-8
m2/L) on smooth, sealed surfaces. Actual coverage may
vary depending on substrate and application method.
May be spray applied at 120-235 sq. ft./gal. (3-6 m2/L).
Recommended Film Thickness: 2.0-5.0 mils (50-125
microns) dry - 5.0-11.0 mils (125-275 microns) wet
Service Temperature Limit: 250°F (121°C) in air.
May discolor at temperatures over 140°F (60°C).
Flame Spread Rating: Class A (0-25) over noncombustible surfaces
Flash Point: Over 200°F (96°C)
Minimum Dry Time (ASTM D 1640) At 3 mils
Substrate Temperature 77°F (25°C)
Minimum Recoat 16 Hours Dry Hard 24 Hours
|
|
Mixing: Slowly add Component B to Component A in a 1:1 ratio. Stir thoroughly and scrape sides of can to ensure thorough blending. Allow the mixed material to stand 45 minutes at temperatures below 70°F (21°C) before use.
Above 70°F (21°C) allow 30 minutes induction time. Always restir before use. Mixed material is usable for six to eight hours; if it thickens, do not add thinner, but discard and mix fresh material. If initial thinning is necessary, use up to one-half pint water per gallon. Do not thin with solvents or solvent thinned coatings. Do not add flow-control materials.
|
Note: Surfaces coated with this product may become slippery when wet. For additional slip resistance in areas of pedestrian traffic, add one to two pounds of non-skid additive per 250 square feet. Fillers must dry overnight before coating.
Drywall - Prime with this product or waterborne primer.
Wood - Prime with this product reduced one-half pint per gallon with water or prime with waterborne primer.
Steel - Prime with waterborne epoxy primer.
Galvanized Metal and Aluminum - Prime with waterborne epoxy primer.
Glazed Brick, Ceramic Tile and Fiberglass - Scuff sand and prime with waterborne epoxy primer.
Previously Painted Surfaces: The waterborne components of this product generally allow use over most old coatings. Old coatings should be tested for lifting. If they lift, remove them. Wash to remove contaminants. Rinse thoroughly with water and allow to dry. Dull glossy areas by light sanding. Remove sanding dust. Remove loose paint. Prime bare areas with primer specified under new surfaces.
|
|
Shelf Life: 1 year minimum - unopened
Mix Ratio By Volume: 1(base - part A):1(converter - part B)
Induction: 30 minutes - above 70°F (21°C), 45 minutes - below 70°F (21°C)
Pot Life: 6-8 hours @ 77°F (25°C)
|
Advantages:
- Chemical and stain resistant
- Resists splash and spillage of alkalis, salts, moisture, oils, grease, foodstuffs and detergents
- Abrasion resistant
- Low odor and a high flash point
- Use over alkyd, latex or epoxy coatings
- Long lasting tile-like finish
- Easily washed and cleaned
- Low VOC
- Performance alternate for Federal Specifications
TT-C-535B (Type II) and TT-C-550C (Class A)
|
|
Warning: The Maximum aged recoat time of this product may be significantly shortened or lengthened by a variety of conditions, including, but not limited to humidity, surface temperature, and the use of additives or thinners. The use of accelerators or force curing may shorten the aged recoat of individual coatings. If the maximum aged recoat window is exceeded, please consult your Original Color Chips Specialist for appropriate recommendations to enhance adhesion. Failure to observe these precautions may result in intercoat delamination.
|
|
Limitations of Use: Not recommended for immersion Service. Exterior exposure will cause early dulling and loss of gloss, but does not affect protective properties.
Epoxy coatings may yellow during application and cure if exposed to the combustion by-products of improperly vented fossil fuel burning heaters.
|
|
Spreading Rate: Apply at 235-320 sq. ft./gal. (6-8 m2/L) or 5.0-7.0 mils wet (2.0-3.0 mils dry) on smooth, sealed surfaces. Actual coverage may vary depending on substrate and application method. May be spray applied at 120-235 sq. ft./gal. (3-6 m2/L) or 7.0-11.0 mils wet (3.0-5.0 mils dry). For best hiding, tint primers toward finish coat color. Certain shades of yellow, All surfaces must be sound, dry, clean and free of oil, grease, dirt, mildew, form release agents, curing compounds, efflorescence, loose and flaking paint and other foreign substances.
|
|
New Surfaces: Concrete, Plaster and Masonry - Cure at least 30 days before painting. pH must be 10.0 or lower. Remove laitance and roughen unusually slick poured or precast concrete by acid etching or sandsweeping. Follow acid manufacturer's application and safety instructions. Rinse thoroughly with water and allow to dry. Remove loose aggregate. Prime with this product thinned 8:1 with water or prime with waterborne epoxy primer. Dry overnight to recoat. Fill concrete
|
WARNING! CAUSES EYE AND SKIN BURNS. HARMFUL OR FATAL IF SWALLOWED. ASPIRATION HAZARD-CAN ENTER LUNGS AND CAUSE DAMAGE. HARMFUL IF INHALED. MAY CAUSE CENTRAL NERVOUS SYSTEM EFFECTS, INCLUDING DIZZINESS, HEADACHE OR NAUSEA. CAUSES RESPIRATORY TRACT IRRITATION.
MAY CAUSE ALLERGIC SKIN REACTION. MAY BE HARMFUL IF ABSORBED THROUGH SKIN. OVEREXPOSURE MAY CAUSE BLOOD, LIVER, KIDNEY DAMAGE. WHEN TINTED, CONTAINS ETHYLENE GLYCOL WHICH CAN CAUSE SEVERE KIDNEY DAMAGE WHEN INGESTED AND HAS BEEN SHOWN TO CAUSE BIRTH DEFECTS IN LABORATORY ANIMALS. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF THE REACH OF CHILDREN.
|
Flash Point: Over 200°F (96°C) 10 gallon kit - 113 lbs. (51.3 kg)
Packaging: 1 gallon kit
1/2 gallon Component A
1/2 gallon Component B
|
|
|
PROPERTIES |
TEST METHODS |
RESULTS |
| Water vapour transmission |
ASTM E- 96
Procedure B-water
(100 microns dry (4 mils dry ) )
|
3.5 perms |
| Abrasion resistance |
ASTM D - 4060
Taber Abraser
CS - 17 wheels
1000 g / wheal
1000 revolutions |
83 mg loss |
Resistance to accelerated weathering
( UVB condensation ) |
ASTM G - 53
12 weeks |
No yellowing
Chalking after one week
Destroyed after nine weeks |
| Tensile strength |
ASTM D - 2370
(90 microns D.F.T (3.6 mils)) |
17.4 MPa
(2,523 psi) |
| Elongation |
ASTM D - 2370
(100 microns D.F.T. (4 mils )) |
5.7 % |
| Adhesion to concrete |
ASTM D - 4541
On concrete |
> 2.0MPa
(>290 psi)
(substrate failure) |
| Static coefficient of friction |
ASTM C - 1028
Dry surface
Wet surface |
0.77
0.66 |
| Toxicity |
Food inspection of Canada |
Approved |
| ASTM D - 1308, spot, covered, 1 and 5 days |
| CHEMICALS |
CONC. |
1 DAY |
5 DAYS |
| ACETIC |
5 |
((3)) |
(3) |
| ACETIC |
10 |
((3)) |
(3) |
| CAUSTIC SODA |
10 |
NON AFF. |
NON AFF. |
| CAUSTIC SODA |
CONC. |
NON AFF. |
NON AFF.> |
| CHROMIC |
10 |
3,7 |
3,7 |
| CHROMIC |
30 |
3,7 |
3,7 |
| CITRIC |
10 |
NON AFF. |
((1)) |
| CITRIC |
50 |
((1)) |
((1)) |
| FLUOBORIC |
10 |
NON AFF. |
NON AFF. |
| FORMIC |
7 |
3 |
3 |
| HYDROCHLORIC |
10 |
NON AFF. |
NON AFF. |
| HYDROCHLORIC |
20 |
NON AFF. |
NON AFF. |
| HYDROCHLORIC |
CONC. |
3 |
3 |
| LACTIC |
5 |
NON AFF. |
(3),5 |
| LACTIC |
10 |
3,5,6 |
3,(5),(6) |
| LACTIC |
15 |
3,5,6 |
3,(5),(6) |
| NITRIC |
5 |
NON AFF. |
NON AFF. |
| NITRIC |
10 |
NON AFF. |
3,((5)) |
| PHOSPHORIC |
5 |
NON AFF. |
NON AFF. |
| PHOSPHORIC |
10 |
NON AFF. |
(6) |
| PHOSPHORIC |
30 |
NON AFF. |
(1),(6) |
| SULPHURIC |
10 |
NON AFF. |
NON AFF. |
| SULPHURIC |
20 |
2,5,7 |
2,5,7 |
| URIC |
CONC. |
NON AFF. |
NON AFF. |
| CHEMICALS |
CONC. |
1 DAY |
5 DAYS |
| POTASSIUM HYDROXIDE |
10 |
NON AFF. |
NON AFF. |
| POTASSIUM HYDROXIDE |
CONC. |
NON AFF. |
NON AFF. |
| SODIUM HYPOCHLORITE |
5 |
NON AFF. |
NON AFF. |
| CHEMICALS |
CONC. |
1 DAY |
5 DAYS |
| ANIMAL FAT |
100 |
NON AFF. |
NON AFF. |
| BEER |
100 |
NON AFF. |
((1)) |
| BUTTER |
100 |
NON AFF. |
NON AFF. |
| CONC. APPLE JUICE |
100 |
NON AFF. |
NON AFF. |
| CONC. ORANGE JUICE |
100 |
NON AFF. |
((1)) |
| COCA - COLA |
100 |
NON AFF. |
((3)) |
| COFFEE |
100 |
NON AFF. |
(3) |
| HONEY |
100 |
NON AFF. |
NON AFF. |
| MUSTARD SEED OIL |
100 |
NON AFF. |
NON AFF. |
| OLIVE OIL |
100 |
NON AFF. |
NON AFF. |
| SOUR MILK |
100 |
NON AFF. |
((3)) |
| SUGAR SOLUTION |
80 |
NON AFF. |
NON AFF. |
| TABLE OIL |
100 |
NON AFF. |
NON AFF. |
| VINEGAR |
100 |
NON AFF. |
NON AFF. |
| CHEMICALS |
CONC. |
1 DAY |
5 DAYS |
| LIPSTICK |
100 |
NON AFF. |
NON AFF. |
| URINE |
100 |
NON AFF. |
NON AFF. |
| CHEMICALS |
CONC. |
1 DAY |
5 DAYS |
| CAR ANTIFREEZE LIQUID |
100 |
NON AFF. |
NON AFF. |
| CAR DIESEL FUEL |
100 |
NON AFF. |
NON AFF. |
| CAR DIFFERENTIAL OIL |
100 |
NON AFF. |
NON AFF. |
| CAR UNLEADED GASOLINE |
100 |
NON AFF. |
NON AFF. |
| CAR GREASE |
100 |
NON AFF. |
NON AFF. |
| CAR MOTOR OIL |
100 |
NON AFF. |
NON AFF. |
| CAR TRANSMISSION OIL |
100 |
NON AFF. |
NON AFF. |
| CAR TURBO OIL |
100 |
NON AFF. |
NON AFF. |
| CAR WINDSHIELD WASHER |
100 |
NON AFF. |
((3)) |
| KEROSENE (JET FUEL) |
100 |
NON AFF. |
NON AFF. |
| SKYDROL |
100 |
NON AFF. |
NON AFF. |
| WHEEL BEARING LUBRICANT |
100 |
NON AFF. |
NON AFF. |
| CHEMICALS |
CONC. |
1 DAY |
5 DAYS |
| ETHANOL * * |
CONC. |
5* |
5* |
| MINERAL SPIRIT |
100 |
NON AFF. |
5* |
| XYLENE |
100 |
NON AFF. |
NON AFF. |
| * * Aseptisation with ethanol as done in pharmaceutical plants (GMP) has no effect on coating.
|
| 1: |
GLOSS REDUCTION |
6: |
SWELLING |
( ): |
MINOR EFFECT |
| 2: |
DISCOLORATION |
7: |
BLISTERING |
(( )): |
BARELY VISIBLE |
| 3: |
STAINING |
8: |
LOSS OF ADHESION |
N.T.: |
NOT TESTED |
| 4: |
FADING / BLEACHING |
*: |
RECUPERATES UPON DRYING |
DESTR: |
DESTROYED |
| 5: |
SOFTENING |
+: |
SEVERE EFFECT |
NON AFF: |
NO EFFECT |
|
Test report available upon request. |
|
|
