|
|
Hours of Operation:
Mon-Fri: 8am - 5pm
Eastern Standard Time
26200 Groesbeck Hwy.
Warren, MI 48089
|
Stay green with our environmentally friendly waterborne epoxy floor coating kits.
|
|
|
|
Original Color Chips High Performance Urethane
( Product Data Sheet )
|
Original Color Chips High Performance Urethane (HPU) is a clear two component polyester/aliphatic polyurethane floor sealer that exhibits excellent characteristics for abrasion resistance, chemical resistance, flexibility, weathering and UV stability.
Recommended for auto service centers, warehouses, computer rooms, laboratories, aircraft hangers, cafeterias, exterior tanks, indoor or outdoor service and chemical exposure areas.
|
PRODUCT NUMBER: HPU 747
SOLIDS BY WEIGHT:
Mixed= 60% (colors); 56% (clear) (+,-2%)
SOLIDS BY VOLUME:
Mixed= 53% (colors); 53% (clear) (+,-2%)
VOLATILE ORGANIC CONTENT:
Less than 3.8 pounds per gallon
RECOMMENDED FILM THICKNESS:
3-5 mils per coat wet thickness (yields 2-3 mils dry)
COVERAGE PER 1.5 GALLON KIT:
400 to 500 square feet @ 3-5 mils wet thickness
PACKAGING INFORMATION
3 gallons 3 gal kit= 2 gallons part A (10.5#/gal-colors) or (8.75#/gal-clear)
and 1 gallon part B (8.5#/gal.) (weights and volumes approximate)
MIX RATIO:
2 parts A to 1 part B by volume
SHELF LIFE:
1 year
FINISH CHARACTERISTICS:
High gloss (>80 at 60 degrees @ Erichsen glossmeter)
ABRASION RESISTANCE:
Taber abrasor CS-17 calibrase wheel with 1000 gram total load and 500
cycles = 20.0 mg loss
IMPACT RESISTANCE:
Gardner Impact, direct & reverse = 160 in. lb. (passed)
FLEXIBILITY:
No cracks on a 1/8" mandrel
ADHESION:
360 psi @ elcometer (concrete failure, no delamination)
VISCOSITY:
Mixed = 200-400 cps (typical, most colors)
DOT CLASSIFICATIONS:
Part A "FLAMMABLE LIQUID N.O.S., 3, UN1993, PGIII"
Part B "FLAMMABLE LIQUID N.O.S., 3, UN1993, PGIII"
HARDNESS:
Shore D = 72
|
CURE SCHEDULE:(70°F)
| pot life - 1 1/2 gallons volume |
2-5 hours |
| tack free (dry to touch) |
2-4 hours |
| recoat or topcoat |
4-8 hours |
| light foot traffic |
14-24 hours |
| full cure (heavy traffic) |
3-5 days |
APPLICATION TEMPERATURE:
45-90 degrees F
CHEMICAL RESISTANCE:
|
| REAGENT |
RATING |
| acetic acid 5% |
C |
| xylene E |
E |
| mek |
B |
| methyl alcohol |
B |
| gasoline |
D |
| 10% sodium hydroxide |
E |
| 50% sodium hydroxide |
D |
| 10% sulfurice |
D |
| 10% hydrochloric acid |
D |
| 20% nitric acid |
C |
| ethylene glycol |
D |
Rating key: A - not recommended,
B - 2 hour term splash spill, C - 8 hour term splash spill, D - 72 hour
immersion, E - long term immersion. NOTE: extensive chemical resistance
information is available through your sales representative.
PRIMER:
This product is not direct-to-concrete. A primer or basecoat is necessary.
LIMITATIONS:
*Colors or gloss may be affected by high humidity, low temperatures, chemical
exposure, or exposure to lighting such as sodium vapor lights.
*For best results use a high quality 3/8" nap roller.
*Substrate temperature must be 5°F above dew point
*All new concrete must be cured for at least 30 days
*Physical properties are typical values and not specifications
*Tire contact may cause staining and discoloration, waiting full 5 days
for full cure is recommended for vehicle traffic
*See reverse side for application instructions.
*See reverse side for limitations of our liability and warranty.
|
|
1) PRODUCT STORAGE:
Store product in an area so as to bring the material to normal room temperature
before using. Continuous storage should be between 60 and 90 degree F.
2) PRODUCT MIXING: This
product has a two to one mix ratio by volume- merely mix two gallons of
part A with 1 gallon of part B. After the two parts are combined, mix
well with slow speed mixing equipment such as a jiffy mixer until the
material is thoroughly mixed and streak free. Avoid whipping air into
the coating. Improper mixing may result in product failure.
3) PRODUCT APPLICATION:
The mixed material can be applied by brush or roller. Maintain temperatures
within the recommended ranges during the application and curing process.
Properly prime the substrate (with basecoat or other sufficient primer).
It is best to maintain a wet edge to avoid roller marks. Direct sunlight
or high temperatures may cause visible roller marking during application.
Too thick of an application may result in solvent entrapment and product
failure.
4) RECOAT OR TOPCOATING:
Multiple coats of this product are acceptable. If you opt to recoat this
product, you must first be sure that all of the solvents have evaporated
from the coating during the curing process. The information on the front
side are reliable guidelines to follow. However, it is best to test the
coating before recoating or topcoating. This can be done by pressing on
the coating with your thumb to verify that no fingerprint impression is
left. If no impression is created, then the recoat can be started. Always
remember that colder temperatures will require more cure time for the
product before recoating can commence. Before recoating or topcoating,
check the coating to insure no contaminants exist. If a blush or contaminants
are present on a previous coat, remove with a standard detergent cleaner.
When recoating this product with subsequent coats of the urethane, it
is advisable to apply the recoat before 24 hour passes. Also, it is advisable
to degloss the previous coat to insure a trouble free bond.
5) CLEANUP: Use ketone solvents or Xylol Xylene.
6) FLOOR CLEANING: Caution!
Some cleaners may affect the color of the floor installed. Test each cleaner
in a small area, utilizing your cleaning technique. If no ill effects
are noted, you can continue to clean with the product and process tested.
7) RESTRICTIONS: Restrict
the use of the floor to light traffic and non-harsh chemicals until the
coating is fully cured (see technical data under full cure). It is best
to let the floor remain dry for the full cure cycle.
|
DANGER!
FLAMMABLE LIQUID AND VAPOR. HARMFUL OR FATAL IF SWALLOWED. ASPIRATION HAZARD
- CAN ENTER LUNGS AND CAUSE DAMAGE. HARMFUL IF INHALED. MAY CAUSE CENTRAL
NERVOUS SYSTEM EFFECTS, INCLUDING DIZZINESS, HEADACHE OR NAUSEA. CAUSES
EYE, SKIN AND RESPIRATORY TRACT IRRITATION. MAY CAUSE ALLERGIC SKIN AND
RESPIRATORY REACTION. OVEREXPOSURE MAY CAUSE BLOOD, LIVER, KIDNEY DAMAGE.
USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF THE REACH OF CHILDREN.
EMERGENCY
PHONE: Chemtrec 800-424-9300 (product code: NPI321)
|
NOTICE
TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY
We warrant that our products are manufactured to strict quality assurance
specifications and that the information supplied by us is accurate to the
best of our knowledge. Such information supplied about our products is not
a representation or a warranty. It is supplied on the condition that you
shall make your own tests to determine the suitability of our product for
your particular purpose. Listed physical properties are typical and should
not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED,
REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE
RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR
IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL
BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH
INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have
no liability for incidental or consequential damages, direct or indirect.
Our liability is limited to the net selling price of our product or the
replacement of our product, at our option. Acceptance of delivery of our
product means that you have accepted the terms of this warranty whether
or not purchase orders or other documents state terms that vary from this
warranty. No representative is authorized to make any representation or
warranty or assume any other liability on our behalf with any sale of our
products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL
INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL
PRECAUTIONS TO PREVENT BODILY HARM.
COPYRIGHT1/1/01
|
|
