|
|
Hours of Operation:
Mon-Fri: 8am - 5pm
Eastern Standard Time
26200 Groesbeck Hwy.
Warren, MI 48089
|
| |
Stay green with our environmentally friendly waterborne epoxy
floor coating kits.
|
|
|
Waterborne Epoxy Basecoat
|
The Original Color Chips Company
26200 Groesbeck Hwy.
Warren, MI 48089
|
|
This epoxy coating is a two - component liquid epoxy emulsion. Applied on interior floors, walls, machinery equipment, it hardens to a tough ceramic - like finish. Particularly suitable on almost any surface, in areas where an inexpensive, easy to clean and wear resistant coating is required.
|
- Water based
- No smell, non - toxic, ideal for in-plant
application during normal operation
- Economical
- Resistant to mild corrosive chemicals
- Highly scrub and wear resistant
- Available In pre - portioned units
- Washable
|
|
All surfaces to be coated should be free of wash, oil, grease or any other contaminant.
Painted substrate: Sand to remove gloss. Scuff to texture existing coating.
|
|
It is recommended to stir part A before adding part B as some soft settling may occur in the containers during storage.
Mix parts A and B mechanically for 5 minutes in recommended proportions.
|
|
Apply material according to the recommendations. |
|
- Consult Material Safety Data Sheet prior to use.
- Do not apply material at temperatures below 60º C (16º F).
- Do not freeze.
- Material might be affected by certain corrosive chemicals.
- Lighter Colors may yellow slightly in sunlight, topcoat with UV-resistant urethane to avoid ambering in sunlight.
|
|
Color: |
Standard colors |
|
|
Solids content: |
Per volume
Per weight
Varies with color |
45%
40-45% |
|
V.O.C.: |
1.7 Ibs / US gallon - varies slightly with color) |
|
|
Mixing ratio: |
1 parts A to 1 part B
(hardener) per volume
|
|
|
Pot life: |
6 hours
|
|
|
Application method: |
Spray, roller, or brush |
|
|
Number of coats: |
1 , 2 for optimum service (thinned out coat/primer coat) |
|
|
Coverage: |
250 ft² Per Kit |
|
|
Recoat time: |
16 - 24 hours |
|
|
Curing time: |
Dry
Full cure |
20 hours
7 days |
|
Thinning solvent: |
Water |
|
|
Cleaning solvent: |
Water |
|
|
Shelf life: |
2 years in original unopened container
|
|
|
Packaging: |
1 US gallons / 3.78 Liters
|
|
|
|
PROPERTIES |
TEST METHODS |
RESULTS |
|
Water vapour transmission |
ASTM E- 96
Dessicant - Procedure A |
0.30 perm |
Abrasion resistance
(Masonite substrate) |
ASTM D - 4060
CS - 17 wheels
1000 g / wheal
3 cycles of 1000 revolutions |
126 mg / cycle |
Direct impact resistance
1. Cement Asbestos Board
2. Galvanized phosphatized steel
|
CGSB 1 - GP - 71 (147.1)
ASTM D - 3029 |
Unaffected at 0.7 J (6 lbs·in)
6.2 J (55 lbs·in) |
|
Scrubbability
|
CGSB 1 - GP - 71 (125.1)
10,000 cycles
|
Unaffected |
|
Gloss before and after 10.000 cycle scrubbsbility |
ASTM D - 523 |
No loss |
|
Toxicity |
Department of Agriculture |
Approved |
|
Adhesion on concrete |
ASTM D - 4541 |
>3.5 MPa
(>500 psi)
(Substrate failure)
|
|
Adhesion on galvanized phosphatized steel
|
ASTM D - 4541 |
>2.1 MPa
(300 psi)
|
CHEMICAL RESISTANCE
ASTM D - 1308, spot test, covered |
|
CHEMICALS |
RESULTS |
|
Detergent 50%, Javel 10%, butter, Lard, sour milk, glucose 20%, motor oil, hydroxide sodium 20% and sat., sodium chloride 20%, potassium chloride 20%, potassium nitrate 20%, sodium bicarbonate 20 and saturated solution, mineral spirit, orange juice conc., hydrogen peroxide 6%, sodium hypo chlorite 5%, sodium carbonate 20%, Oakite 1%, Orvus |
Not affected |
|
Lipstick (red) |
Pink stains |
|
Coffee |
Yellow stains |
|
Beer, gear grease, Coca-Cola, olive oil, urine |
Slightly yellowish stains |
|
Soap 2%, ethyl alcohol 50%, JP 4 jet fuel, toluene, acetone, ethyl acetate, ethyl, citric acid 10%, acetic acid 3%, ammonium hydroxide |
Slight softening (partial recovery
when dry after 24 hours) |
|
Hydrochloric acid 10 & 20% |
Blisters, slight yellowing |
|
Chromic acid |
Brown stains, loss of gloss |
|
Lactic acid 10%, nitric acid 10 & 20%, sulphuric acid 10, 20 & 50% |
Affected |
|
Test report available upon request. |
|
|
